Aury news.
The Aury horizontal vibrating centrifuge (WSL Series) is a suitable granularity coal drainage. It is easy to operate maintain, has a high level of drainage efficiency, low power consumption and few wear parts.
Nov 23 2023
Another Happy Aury Customer
Another screen on its way to one of our valued customers.
Aury recently completed the assembly and testing of a single deck banana screen for a Central West NSW customer.
If you are looking for a reliable and cost effective screen please reach out to our sales team.
Aury recently completed the assembly and testing of a single deck banana screen for a Central West NSW customer.
If you are looking for a reliable and cost effective screen please reach out to our sales team.
Nov 23 2022
First screen delivery to WA customer
Aury Australia is growing rapidly in Western Australia in the mineral processing industry with another big screen project rolling out of the workshop recently.
Our recent opening of the new facility has benefits to our customers in Western Australia where Aury can assemble, paint and test some of the largest vibrating screens in the industry. Aury can also refurbish their exciters.
Please contact Aury for more information.
Our recent opening of the new facility has benefits to our customers in Western Australia where Aury can assemble, paint and test some of the largest vibrating screens in the industry. Aury can also refurbish their exciters.
Please contact Aury for more information.
Aug 31 2022
Big Red - Aury Mass Casting
Aug 2022 Aury Australia recently delivered and installed a replacement VM1500 Centrifuge mass casting for one of our Bowen Basin CHPP customers. The brand new mass casting was supplied in Aury red so as to set it apart from the other non-Aury mass castings. Our client was very happy with the installation work completed by the Aury service Team and most importantly the performance of the equipment. If you are looking for cost effective wash plant equipment and consumables please contact Aury Australia.
Jun 23 2022
Successful Project Delivery
Aury Australia recently carried out a significant vibrating screen installation project for Glencores Ravensworth CHPP in the NSW Hunter Valley
As part of this highly complex project the Aury installation team worked more than 2000 total hours over 15 days to dismantle & remove four 4.2m x 7.3m vibrating screens and then reinstall new four new Aury screens piece by piece.
The project was a huge success for both Ravensworth CHPP and Aury Australia:-
Delivered incident and injury free
Delivered ahead of time
As part of this highly complex project the Aury installation team worked more than 2000 total hours over 15 days to dismantle & remove four 4.2m x 7.3m vibrating screens and then reinstall new four new Aury screens piece by piece.
The project was a huge success for both Ravensworth CHPP and Aury Australia:-
Delivered incident and injury free
Delivered ahead of time
Jun 17 2022
Aury Australias Western Australia Facility Open Day
On Wednesday the 18th of May 2022 Aury Australia held the Grand Opening Day of its new facility at 27 Purser Loop, Bassendean Western Australia. The new facility not only marks a huge milestone in our journey to increase Aury Australias footprint in Western Australia, but provides confidence to the industry around our commitment and support.
The event was very successful as we had guests attend from numerous Mining Companies and Engineering Firms based in the region. Everyone had the opportunity to gain knowledge about Aury Australias quality products, to walk through our facility and to meet with the Aury Australia team. Our new facility is a purpose designed facility set up to support the suite of the Aury Australia products into the Western Australia market particularly our screen builds, exciter rebuilds and services.
The event was very successful as we had guests attend from numerous Mining Companies and Engineering Firms based in the region. Everyone had the opportunity to gain knowledge about Aury Australias quality products, to walk through our facility and to meet with the Aury Australia team. Our new facility is a purpose designed facility set up to support the suite of the Aury Australia products into the Western Australia market particularly our screen builds, exciter rebuilds and services.
Apr 27 2022
Case Study Double Deck Screen Media Optimisation
<p>Over a 4-month period early in 2022, Aury Australia have been working with our South East Asian customer to solve their process issues. With travel restrictions there was a lot of email communication and some video conferencing. We hope to be back on site very soon.
Our customer was having issues with cone and jaw crusher breakdowns, pegging of screen media and unplanned shutdowns to either repair or clean screen media and/or crushers. These issues prevented the client moving forward with any plans for increased production.
Being the screen media is ahead of the crushers, they wanted initial help with their screen media. The media layout or design hasn’t changed too much since the process started over 8 years ago.
Photos were sent of what the decks would look like after a short period of operation, never getting better. Our customer persevered with this issue but were suffering from more frequent maintenance and repairs recently while wanting to increase production levels. These higher levels were not achievable in the current situation.
The screen has two decks. The top deck, while relatively unpegged, did have apertures along the fixing rails. It was clear that the rock size passing was too large for the fixing rail protection “wings” to pass resulting in the rock jamming (pegging) and then being filled with fines. This reduced panel open area from a design of 42% down to lower than -32%. Being an opposition type fixing rail with large protection “wings” used to protect stringer rails the solution needed to be innovative. The second deck used a series of square apertures at different sizes down the screen. There were a total of 3 different aperture steps. Unfortunately, the pegging of apertures was quite severe.
The loading on the screen was not seen as an issue considering the aperture sizes but the fines presenting at the discharge was. The crusher issues were a result of these fines.
A PSD was sent to Aury. A meeting was organised to discuss the customers required size fractions according to their process limits. A few possible solutions were presented to our customer. These were discussed and refined. The solution for both decks was to install slotted apertures. On the top deck the apertures were moved in and away from the fixing rail protection strips while still maintaining the open area. On the bottom deck the apertures were staggered and 3 rows of 50mm high cross dams added to slow and roll the material. The open area was slightly improved.
The new panels were manufactured, delivered to meet the planned crusher service schedule and installed without issue. The photos show the decks 2 weeks post install. The feed end impact top deck panels still showing the same issue but they will be improved in the next round.
The instant result was our customer not experiencing any pegging and struggling to choke feed their crushers! This allowed them to try new things in terms of TPH, feeder rate increased and crushing sizes. Below you will see that the Amps consumed has lowered by 12%, their TPH have increased, and their recirculating load has dropped.
The opportunity to work with our customer has allowed them to save money in power by reducing the Amps from an average of 2.3Amp h/T to <1.7Amp h/T, even with a feeder speed increase. It has reduced their planned and unplanned shutdowns and increased available screening/crushing hours. It has allowed them to increase their throughput from an average of 400TPH to >500TPH while reducing their average recirculating load by approx. 24%. Our customer can now move their attention to other areas to improve efficiency. We thank their team involved. This was a great result for them.
For more information, please contact your Aury Australia representative or by visiting our web site https://www.auryaustralia.com.au/contact or by emailing us at Sales@AuryAustralia.com.au</p>
Our customer was having issues with cone and jaw crusher breakdowns, pegging of screen media and unplanned shutdowns to either repair or clean screen media and/or crushers. These issues prevented the client moving forward with any plans for increased production.
Being the screen media is ahead of the crushers, they wanted initial help with their screen media. The media layout or design hasn’t changed too much since the process started over 8 years ago.
Photos were sent of what the decks would look like after a short period of operation, never getting better. Our customer persevered with this issue but were suffering from more frequent maintenance and repairs recently while wanting to increase production levels. These higher levels were not achievable in the current situation.
The screen has two decks. The top deck, while relatively unpegged, did have apertures along the fixing rails. It was clear that the rock size passing was too large for the fixing rail protection “wings” to pass resulting in the rock jamming (pegging) and then being filled with fines. This reduced panel open area from a design of 42% down to lower than -32%. Being an opposition type fixing rail with large protection “wings” used to protect stringer rails the solution needed to be innovative. The second deck used a series of square apertures at different sizes down the screen. There were a total of 3 different aperture steps. Unfortunately, the pegging of apertures was quite severe.
The loading on the screen was not seen as an issue considering the aperture sizes but the fines presenting at the discharge was. The crusher issues were a result of these fines.
A PSD was sent to Aury. A meeting was organised to discuss the customers required size fractions according to their process limits. A few possible solutions were presented to our customer. These were discussed and refined. The solution for both decks was to install slotted apertures. On the top deck the apertures were moved in and away from the fixing rail protection strips while still maintaining the open area. On the bottom deck the apertures were staggered and 3 rows of 50mm high cross dams added to slow and roll the material. The open area was slightly improved.
The new panels were manufactured, delivered to meet the planned crusher service schedule and installed without issue. The photos show the decks 2 weeks post install. The feed end impact top deck panels still showing the same issue but they will be improved in the next round.
The instant result was our customer not experiencing any pegging and struggling to choke feed their crushers! This allowed them to try new things in terms of TPH, feeder rate increased and crushing sizes. Below you will see that the Amps consumed has lowered by 12%, their TPH have increased, and their recirculating load has dropped.
The opportunity to work with our customer has allowed them to save money in power by reducing the Amps from an average of 2.3Amp h/T to <1.7Amp h/T, even with a feeder speed increase. It has reduced their planned and unplanned shutdowns and increased available screening/crushing hours. It has allowed them to increase their throughput from an average of 400TPH to >500TPH while reducing their average recirculating load by approx. 24%. Our customer can now move their attention to other areas to improve efficiency. We thank their team involved. This was a great result for them.
For more information, please contact your Aury Australia representative or by visiting our web site https://www.auryaustralia.com.au/contact or by emailing us at Sales@AuryAustralia.com.au</p>
Jun 25 2021
Aury win big in Mackay
Sunday June 6th: The Aury Australia Mackay branch completed the BMA Mackay Marina run, a 5km Corporate challenge. The 5km corporate challenge is a great opportunity for groups to raise much needed funds for the Leukemia Foundation. Teams are encouraged to fundraise within their workplace, group or school. There is friendly rivalry between teams to fundraise and make a difference in the lives of those with blood cancer.
Knowing the teams greatest strength isnt fitness we opted to go for best dressed. Donning red Tutus, red wigs and face paint in our Aury uniforms we set off to complete the run. Matt Collins, Jamie Lowien and Hayden Sparks headed up front to give us a fighting chance in a good time.
Below are the results of the day:
Matt Collins completed the race first in a time 23.45,
Jamie Lowien came in second with a time of 28.57
Hayden Sparks, after a quick spew n go at the 2km mark, came in with a time of 36.06. Hayden has decided pre workout beers isnt a good idea!
Jerremy Mann put in a solid effort with a time of 43.32
Dusty Sinnamon took off running after chatting with the girls for 2.5km, brought It home with a 47.34.
The mum club, Danielle and Tiarne hung at back with the cool kids and commentated the race. Matt Collinss daughter made us break a sweat crossing the line in 51.08.
After the race was done it was clear who the best dressed contenders were. Aury was in the lead!! After waiting for what seemed like forever to hear the actual results of the runners, we waited to hear the results of the best dressed. This was our time to shine. They called it, AURY AUSTRALIA wins the BEST DRESSED. Out of 4000 runners, and 172 Teams, we were the BEST!
Congratulations team.
Knowing the teams greatest strength isnt fitness we opted to go for best dressed. Donning red Tutus, red wigs and face paint in our Aury uniforms we set off to complete the run. Matt Collins, Jamie Lowien and Hayden Sparks headed up front to give us a fighting chance in a good time.
Below are the results of the day:
Matt Collins completed the race first in a time 23.45,
Jamie Lowien came in second with a time of 28.57
Hayden Sparks, after a quick spew n go at the 2km mark, came in with a time of 36.06. Hayden has decided pre workout beers isnt a good idea!
Jerremy Mann put in a solid effort with a time of 43.32
Dusty Sinnamon took off running after chatting with the girls for 2.5km, brought It home with a 47.34.
The mum club, Danielle and Tiarne hung at back with the cool kids and commentated the race. Matt Collinss daughter made us break a sweat crossing the line in 51.08.
After the race was done it was clear who the best dressed contenders were. Aury was in the lead!! After waiting for what seemed like forever to hear the actual results of the runners, we waited to hear the results of the best dressed. This was our time to shine. They called it, AURY AUSTRALIA wins the BEST DRESSED. Out of 4000 runners, and 172 Teams, we were the BEST!
Congratulations team.
May 11 2021
New Screen and Media for a Bowen Basin Customer
Aury Australia proudly dispatching an ABS2461 vibrating screen complete with Aury wedge wire screen media from our Rutherford facility last week.
Our high quality vibrating screen and the accompanying screen media, which will be installed on the customers existing screens, will be travelling to a coal mine in the Bowen Basin.
This screen comes with the Aury rubber enclosed springs also. Painted, assembled, fitted media, tested and FAT by our customers representative well ahead of schedule, Aurys smart supply chain and project planning means another valuable customer will receive their equipment ahead of time.
Thank you to our loyal customers for your continued support.
Our high quality vibrating screen and the accompanying screen media, which will be installed on the customers existing screens, will be travelling to a coal mine in the Bowen Basin.
This screen comes with the Aury rubber enclosed springs also. Painted, assembled, fitted media, tested and FAT by our customers representative well ahead of schedule, Aurys smart supply chain and project planning means another valuable customer will receive their equipment ahead of time.
Thank you to our loyal customers for your continued support.
Aury Service
The World-class Aury service starts from your first enquiry.
Aury Australia manufactures polyurethane screen media using high quality urethane raw polymers that provide high abrasion resistance resulting in longer service life. Our vast aperture library allows us to provide the best solution.
View Aury Services
Get in contact with Aury.
Aury Australia manufactures polyurethane screen media using high quality urethane raw polymers that provide high abrasion resistance resulting in.
Get In Contact
